V-TAC

Outdoor Up/Down Wall Light V-TAC VT-120112-W 10W LED 1250lm CCT 3in1 IP65 White

Name: Outdoor Up/Down Wall Light V-TAC VT-120112-W 10W LED 1250lm CCT 3in1 IP65 White
Brand: V-TAC

The VT-120112 in white is a small facade wall light shaped as a column, 71 x 71 x 171 mm. Light leaves it in two streams - up and down - drawing a pair of symmetrical cones on the wall. It does not light the space in front of it; its job is to bring out the texture of a wall, an entrance or a gate pier. Adjustable beam spread, 0-90° This is unusual at this price and the biggest difference from an ordinary up-down fitting. The beam can be set anywhere between 0 and 90°: at zero you get two narrow, hard lines of light hugging the wall; at 90°, broad soft fields that cover a larger stretch of facade. The same fitting can therefore work as an accent picking out the joints in stone, or as practical light beside a front door. 3-in-1 colour switch Inside the housing sits a CCT switch with three positions: 2700 K, 3200 K and 4000 K. The colour is chosen once, at installation - once the fitting is closed the switch is out of reach, so the decision is best made before the body is bolted onto the base plate. 2700 K is very warm and suits timber and brick; 3200 K sits in between; 4000 K gives a neutral white that reads better on a driveway or steps. Dimming is not provided for - the fitting runs at full output only. Light output The SMD LED module draws 10 W and delivers 1250 lm, an efficacy of 125 lm/W - a very good figure for an exterior fitting. Colour rendering is above 90 and the red component R9 is 55; at that level brick, timber and rust-coloured render keep a saturation that CRI 80 fittings cannot give them. Colour consistency falls within 6 MacAdam ellipses, so a row along a facade will light in one shade. Start-up is instant - 0.001 s to full brightness. Durability and installation The housing is white-painted aluminium. IP65 means fully dust-tight and resistant to water jets; IK06 covers impact up to 1 J. Installation starts by removing the base plate with the supplied allen key; the plate then serves as a drilling template, and plugs and screws are included. The cable goes onto the terminal block - the manual explicitly requires proper earthing and connection by a qualified electrician. Finally the body slides onto the base and is locked with the set screws. In service Rated life is 20,000 hours over more than 15,000 switching cycles - at two hours a day, over twenty years. The light source is integrated and not replaceable: the manual states plainly that at end of life the whole luminaire is replaced. Energy class is E and the declared power factor is above 0.7. The warranty runs 2 years, assuming 10-12 hours of operation a day. Variants VT-120112 comes in three body colours: white (code 24345, offered here), black (24346) and corten (24347). All share identical electrical and optical figures - the choice is only whether the fitting should disappear against pale render or stand out from it. SpecificationOrder code: 24345, product code VT-120112 (white version)EPREL number: 2590109, energy class EType: facade wall light, up-and-down outputLight source: integrated SMD LED, not replaceablePower: 10 WLuminous flux: 1250 lmEfficacy: 125 lm/WColour temperature: switchable 2700 K / 3200 K / 4000 KColour rendering: CRI > 90 (R9 = 55)Beam angle: adjustable 0-90°Supply: 220-240 V, 50 Hz, power factor > 0.7Ingress protection: IP65, impact rating IK06Dimensions: 71 x 71 x 171 mmMaterial: aluminium, whiteLifetime: 20,000 h, over 15,000 switching cyclesStart-up: 0.001 s to full outputDimmable: noWarranty: 2 yearsMostrar mais

desde 62,58 €

1 oferta

Ver ofertas